 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| WJZ1010 Broadband Surface Mount Mixer Product Features x x x x x x x +22 dBm Input IP3 RF: 1 - 2500 MHz LO: 1 - 2500 MHz IF: 1 - 2000 MHz +13 dBm LO Drive Level No Internal Solder Connections Lead Free/RoHS complaint SMT package x No External Bias Required Product Description The WJZ1010 is a passive double-balanced diode-ring mixer that provides high dynamic range performance in a Lead Free/ RoHS-compliant surface mount package. The mixer is nominally driven with a LO input power of +13 dBm to optimize its performance. Other WJZ models are available for other LO drive levels. Targeted applications include frequency up/down conversion, modulation and demodulation for receivers and transmitters used in 2.5G and 3G GSM/CDMA/W-CDMA systems. The device can also be used in Radar, Satellite, Test / Medical Instruments, Avionics communications and Navigation markets. Functional Diagram 1 2 3 LO 8 4 RF 7 6 IF 5 Top View Applications x x x x Up/down frequency conversion Phase Detector Image Rejection Current Controlled Attenuator Specifications Parameter SSB Conversion Loss RF/LO = 10-1300 MHz, IF = 10-1000 MHz RF/LO = 10-2500 MHz, IF = 30-1000 MHz Port-to-Port Isolation L-R = 10-2000 MHz L-R = 10-2500 MHz L-I = 10-2000 MHz L-I = 10-2500 MHz R-I = 10-2200 MHz 3rd Order Input Intercept Point 1dB Input Compression Point VSWR RF Port = 600-1200 MHz RF Port = 1200-1800 MHz RF Port = 1800-2500 MHz LO Port = 600-1200 MHz LO Port = 1200-1800 MHz LO Port = 1800-2500 MHz IF Port LO Drive Level Units dB dB dB dB dB dB dB dBm dBm Min Typ 6.5 7.4 Max 8.5 9.5 Notes See note 1. Guaranteed at 8 dB max at 25 oC See note 1. Guaranteed at 9 dB max at 25 oC 21 17 20 16 38 37 34 33 25 +22 +9 1.9:1 1.8:1 1.8:1 1.3:1 1.8:1 1.8:1 1.2:1 +13 IF = 100 MHz IF =100 MHz IF =100 MHz dBm 1. Measured in a 50 ohm system with a nominal LO drive of +13 dBm, low side LO, in a downconversion application with LO = 2100 MHz, RF = 2200 MHz, IF = 100 MHz. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature RF Input Power -40 to +85 qC -65 to +100 C +19 dBm Rating Ordering Information Part No. WJZ1010 WJZ1010-PCB Description Broadband Surface Mount Mixer Fully-Assembled Mixer Application Board Operation of this device above any of these parameters may cause permanent damage. Standard T/R reel size = 500 pieces on a 13" reel. Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x Web site: www.wj.com Page 1 of 3 April 2007 WJZ1010 Broadband Surface Mount Mixer Performance Charts Input IP3 vs RF Frequency 30 Input IP3 (dBm) IF = 100 MHz, LO = 13 dBm, +25 UC Conversion Loss vs RF Frequency 5 Conversion Loss (dB) IF = 100 MHz, LO = 13 dBm, +25 UC 25 20 15 10 0 500 1000 1500 2000 RF Frequency (MHz) 2500 6 7 8 9 10 0 500 1000 1500 2000 RF Frequency (MHz) 2500 LO VSWR vs Frequency 2.4 2.2 2.0 2.2 RF VSWR vs Frequency IF = 100 MHz, +25 oC 2.0 VSWR VSWR 1.8 1.6 1.4 1.2 1.0 0 500 1000 1500 Frequency (MHz) 2000 2500 1.8 1.6 1.4 1.2 1.0 0 500 1000 1500 RF Frequency (MHz) 2000 2500 1.4 1.3 VSWR IF VSWR vs Frequency IF=50MHz IF=100MHz IF=150MHz 60 50 40 30 20 Isolation vs LO Frequency IF = 100 MHz, +25 UC L-I Isolation (dB) L-R 1.2 1.1 1.0 0 500 1000 1500 LO Frequency (MHz) 2000 2500 0 500 1000 1500 LO Frequency (MHz) 2000 2500 Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x Web site: www.wj.com Page 2 of 3 April 2007 WJZ1010 Broadband Surface Mount Mixer Mechanical Information This package is lead-free/RoHS-compliant. The plating material is lead-free Tin (Sn). It is compatible with lead-free (maximum 260qC reflow temperature) and recommend 245qC reflow temperature soldering processes. Also recommend adding active flux of 2% during solder reflow. Application Circuit WJZ1010 PIN 8 PIN 4 LO PIN 6 RF IF Notes: 1. Circuit board material: .021" FR-4, 2 layers, .025" total thickness 2. Blocking capacitors are required on the ports (pins 4, 6, 8) if any dc signal is present. Outline Drawing Product Marking The component will be marked with a "WJZ1010" designator followed by an alphanumeric lot code on the top surface of the package. WJZ1010 XXXX Tape and reel specifications for this part will be located on the website in the "Application Notes" section. Functional Pin Layout 1 2 3 Land Pattern / Mounting Configuration LO 8 4 RF 7 6 IF 5 Top view Pin No. 4 6 8 1,2,3,5,7 Backside Metal Notes: 1. Ground vias are critical for RF grounding considerations. 2. A minimum of 12 ground vias underneath the device is required. 3. Trace width depends on the PC board material and thickness Function RF IF LO GND Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x Web site: www.wj.com Page 3 of 3 April 2007 |
Price & Availability of WJZ1010-PCB
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |